Видео

Isolation valves on these are a nightmare

Others show bleeding air at end not start. Seems more right.

Have I just watched an advert so I can watch an advert ? ffs.

Put vaseline or silicone spray or corrosive grease on the top screw threads of the cap and it won't seize up.

Are you aware that your product became hard to service? Top cover become seized and quick release trigger not work every time? Maybe some videos about that?

How do you open the lid if it is too tight

so how many times can this be used ?? I was sent a demo jar i see it already has this black sludge on it w water moisture ..... so after I try this in my own home and wipe away sludge now what? how do we replace the black sediment in it ?? or is that just some 1 time use thing and the next time the demo jar is used we don't need that black sediment in it ??

Hi I don't have a magnaclean Pro 2 installed. So is there a way to attach the hoses to the central heating system without the magnaclean attachment? Thanks

Türkiye temsilcisi kim ?

what do you do to keep pump running when boiler has got to temperature and system won't circulate. is there a way of just keeping pump running

Hello Adey Can this particular model be used with black iron pipe rather than copper pipe?

great, the only thing is rust is virtually non-magnetic. it will catch some iron oxides, but not all. a lot of it will still get into the head exchanger and block it up. Why doesn't this have a mesh filter of some sort?

Make is easy to buy a spare spanner. My wife threw it out because it was inside the empty magnaclean box

I'm struggling to find room to install in return pipe near boiler. Easiest place I can find is in a vertical run of 15mm pipe. Would this be ok?

Bonjour . Existe-il un réseau de distributeur en France.Merci

can they be fitted on a horizontal return pipe?

The video doesn't show the bottom nut being replaced after draining out the water - watched it a couple of times. It would be good if the video could be updated to include an extra step for replacing the bottom nut before adding inhibitor and opening the isolation valves.

Fantastic product love it

MagnaClean takılan kombiler uzun yıllar sorunsuz çalışır.

Türkiye'de MagnaClean ürünlerini satın almak için 0536 256 43 43 nolu telefonu arayabilirsiniz

Türkiye'de MagnaClean ürünlerini satın almak için 0536 256 43 43 nolu telefonu arayabilirsiniz

A good simple how to, but not sure how I'd apply that in the real world. Perhaps you can help? I own a Magnacleanse, but not yet used it on its own i.e. without a powerflushing pump. The question I have for you is how you can drain a system via the flexible hose when the connections are at a higher level than the base of radiators. It would seem that, in practice, you'd still have to drain at a low point to get all, or nearly all the water out. Let's face it: many, many, systems have radiators on several drops and some drops have no drain valves, so you are stuck with slackening off the compression nuts and catching water in a cat litter type tray to achieve full drainage. How essential is it to remove all the residual MC5? The fact that it is 'suitable for all systems' suggests it is non acidic, but does that mean a simple drain down is sufficient, even if there may be a few litres of water left in the system?

Türkiye'de MagnaClean ürünlerini satın almak için 0536 256 43 43 nolu telefonu arayabilirsiniz.

Türkiye de MagnaClean ürünlerini satın almak için 0536 256 43 43 nolu telefonu arayabilirsiniz.

Türkiye de MagnaClean ürünlerini satın almak için 0536 256 43 43 nolu telefonu arayabilirsiniz.

Big black dildos

I put one in fantastic the amount of crap that came out of the system 👍👍👍👍

Hi, Had my Magnaclean Pro 2 for about 3 years, and have just gone to clean it but the quick release will not release, is there anything I can do??? I have taken it apart and cleaned the filter spindle and have done everything apart from remove the unit from the pipework so cant give it a good clean :( Please help as paying a plumber to do somthing simple would not be good :( @Adey

Unbelievable 😂

Regarding "leaking" of this product - (see leck 31 and M Guest below) . I think there is a flaw in the design / install instructions of this product - and indeed .... confusion in the actual fitting instructions which don't specifically refer to compression fittings ends "A" and "B" - and ... which goes uppermost * ( the only thing that does imply this is with the diagrams in the instructions showing shut off taps facing forward... ( and I couldn't fit this way - they had to fit facing the other way - with the magnafilter facing forwards) ( * And does that actually matter - since it is said later on that the flow direction doesn't matter - but - since "one" end has a defined length that the pipe can enter the compression fitting .. and the other end allows "slip" .. .then it makes for easier fitting if the defined length fitting is placed lower most so gravity /weight of the unit assists the assembly of the lower compression joint .,, ensuring the pipe enters the fitting fully ---- HOWEVER - see below ** ( Note - only place instructions refer to "A" and "B" is "where " in the CH "flow" circuit where the product should or should not be fitted The basic problem as I see it is: Removing 150 mm of pipe actually leaves very little pipe entering into each compression joint !!, ( ie I think its TOO long !! -see my notes below) So - If you aren't careful - you can end up with one compression olive very close to the end of the pipe - see : **!! -and that means a likely hood of a poor seal from the olive; - and - I think what then happens is .. because it takes a fair amount of torque to remove the cap for access to the magnetic filter inside for cleaning etc .. it is very easy to "rotate " the whole unit on the compression joints if they aren't "tight" - and ... as we all know ... disturb a compession joint at your peril !! .. ... and then it weeps .. and the only real solution to that is dissasmble it ( ie Drian the *****y system AGAIN ) - clean - and re-seat the olive . I reckon this is WHY the product leaks ( **!! as I did as I had to install this product " with the shutoff valves facing the OTHER direction for that shown in the video - as They could not be easily accessed if fitted facing forward ) - which means the compression fitting / shutoff valve with the shorter "internal bore" is uppermost - and the "long bore" port lowermost - So ... I resolved this problem by replacing the lower length of pipe ( that of course I'd now cut !!! in my installation ( it was fairly easy as there was only about 300mm of this pipe to a soldered 22mm equal tee - and quickly heating this joint - removing pipe - and replacing with another pipe of length about 15mm longer ( ie reducing the "cut" length from 150mm to 135mm - which then meant the pipe on the shorter bore end fits against the step in diameter ( as it would on any usual compression fitting .. and ... the other "new" end is now long enough to fit well into the other "slip" end thus ensuring the olive fits snug .. and there is sufficient pipe "inside" the fitting to ensure a secure joint In this case - the product fits as one would expect - pipes nice and secure - and no movement of the unit when the cap is removed / refitted Or put another way .. don't cut 150 mm - more like 135 mm ?

How do you know when radiator is 1/2 full ?? - and -exactly how do you control that ? ( dudicous use of bleed valve ?? ) - think you conveniently skipped over this vital part - which impacts on the successful removal of debris using vibration from sds drill?

Was the magnet clean before the start of the demo?

We bought one as a family( that’s 4 houses) as it not cheap around half a grand and it’s saved so much time flushing the rads etc 🤑

at which point in video do we put screw back in bottom? i mean when u refill with inhibitor it will piss out bottom

yes I have heard that they are bad for leaking I have heard scotish gas has stopped fitting them as they have so much trouble

Great Presentation!

Does it work, and anyone selling these in Norway?

Not entirely sure i can recommend,i have this Magnaclean micro 2 installed on my boiler and its started leaking after only 13 months use.

Not trying to be 'that guy' but you've got a spelling error in the description. Also, how does the unit auto bleed off the air introduced when cleaning? Is that manual with the valve or does it just get pushed into the central heating network? If it is manual, surely the pressure release valve would squirt water out when you use it (assuming you bleed out all of the air). Thanks :)

100% the best system to fit.

I've got one of these!

Very interesting and I can see it works. Are these available in Canada?

this is the best filter i have ever installed, well done adey! i am impressed and install it on every boiler i put in!

Hi, 'multiple installation options', I can see that but is there a particular direction of flow through the filter?

Our new video shows the development process of our new innovative chemical range! ruclips.net/video/pIXUKwfR6jU/видео.html ‪#‎RadiatorChemicals‬ ‪#‎ADEY‬

How do we attach a MagnaCleanse to this?

So how do we attach a Magnacleanse to the pro2?

What great advice! Yes the MagnaClean could save every house hold up to 6% year on year on their Heating Bills! #ADEYHH14

really glad this as been fitted our rads were full of sludge